CES GPS-205 User Manual

DP-1000SUSER MANUALFor programming these devices:GPS-201/GPS-202GPS-205GPS-206GPS-208PT-101CES WIRELESS TECHNOLOGIES, CORP.925-122 South Semoran Boule

GSM Registration Reset Options: This option provides the capability of having the device perform a soft reset when it cannot connect to the GSM networ

MinimumTime(seconds)MaximumTime(seconds)Distance(meters)Description0 0 0 Time/Distance Reporting is disabled.0 0 1000 Position is sent every 1000 mete

Figure 6: Other GPS OptionsEnable GPRS Queue: Enabling the GPRS Queue instructs the device to store its packets if GPRS is unavailable. This is import

2.4 GPS201 and GPS-202 OptionsThe GPS-201 and GPS-202 support one input and an ignition input. The configuration of these are discussed in this sectio

Input 1: If a position packet is to be generated when the state of Input 1 changes, check Enable in the Input 1 section. Figure 10: Input 1 Reporting

GPS Status Reporting Options: The status of the GPS signal can sent, if desired. It can be sent when the signal is valid and when the signal is invali

detects that it has entered or exited a GeoStatus area it will perform the programmed action and will not look for any other GeoStatus actions.Figure

Figure 16: GeoStatus Configuration DetailsEnter the information for the GeoStatus on this form. The coordinates are entered in decimal degrees. The va

Figure 17: SMS OptionsDestination: To configure the GPS-205 to send an SMS check Enable and then select the destination. The destination can be an e-m

NOTE: By default the output is in the high state.Figure 18: GPS-206 I/O Options (both Inputs 1 and 2 are enabled)2.6.1.1 Input 1 Input 1 can be disabl

TABLE OF CONTENTSTABLE OF CONTENTS...

When the input is enabled to send on low to high state change it will send a packet indicating this state change. It will not send a packet when the s

Figure 21: Advanced Input Configuration - Enabled2.6.1.1.3 CallInput 1 on the GPS206 can be used to place a call to one pre-programmed number, to answ

2.6.1.2 Input 2The options for Input 2 are the same as those for Input 1 with the exception that only Input 1 can be used to place or answer calls. 2.

Input 5, Idle State: The final option is for the unit to send its idle state. The GPS-206 can be configured to not send its state, to send a moving st

FleetLinc the coordinates of this point will be displayed in the lower right corner. In PowerTrak3 the coordinates of the point will be displayed in t

If interfacing the GPS-206 to a Garmin Nüvi PND the interface needs to be enabled in the GPS-206. This is done by checking the Enable Garmin FMI check

Input 3: Input 3 can send a packet when its state goes low, when it goes high, or for both state changes. See note above.NOTE: Depending upon programm

Figure 29: PT-101 GPS Status Reporting OptionsThe PT-101 uses Input 4 to report the state of the GPS signal. If programmed to send a packet when GPS i

required to trigger an GeoStatus Entry or GeoStatus Exit event. It prevents a false reading when the device is on the threshold of the GeoStatus.Set G

Note: The use of SMS often requires the entry of a Gateway Number. Please contact your cellular service provider to see if this is required and, if so

FIGURESFigure 1: Device Selection...

Figure 36: PT-101 User Defined Button OptionsTo enable the User Defined Button check Enable. Now select the desired action. If selecting a Status Key

Figure 38: File MenuOpen: This selection allows an existing device configuration file to be opened. The default location for the configuration files i

Figure 40: Select Com PortFor the correct com port to use with the GPS-208 or PT-101 follow these steps. Note: The driver for the GPS-208 or PT-101 mu

2.13 Program MenuThe selections on the Program are: Set to Factory Defaults, Read System Information, Compare System Information and either Mode-Manua

Figure 43: Sequential programming prompt.Note that the Unit ID entered will be the first one programmed. To start the sequential programming click OK.

Figure 46: Begin programming from a file prompt.To begin the programming from a file process click the Yes button. A file dialog will now be displayed

GPRS Connection CommandsThis section provides the functionality to determine if the attached device is able to successfully access and connect to the

© CES Wireless Technologies Corp – 2011 Page 37 of 50

Verify GPRS Status: This button sends a command to the attached device to verify if it is registered on the GPRS network. The possible responses to th

• service option not supported• requested service option not subscribed• service option temporarily out of order• NSAPI already used• protocol errorsT

Figure 50: Verify GPRS Status response...38Figure 51:

3.0 SupportIf you need help, we are easily accessible ….Telephone: Call 407-679-9440, and ask for product support.Fax: 407-679-8110Email: support@c

Appendix A: Installing the Device Drivers for the PT101In order for the computer to recognize the PT101 device the device drivers for the PT101 must b

Choose the Install from a list or specific location (Advanced) selection and click Next.Figure 56: Found New Hardware Wizard Screen 3Select the option

Figure 58: Windows logo verificationIf it does click on the Continue Anyway button.Figure 59: Found New Hardware Wizard Screen 5Click on Finish. The W

Appendix B: Installing the Device Drivers for the GPS-208In order for the computer to recognize the GPS-208 device the device drivers for the GPS-208

Choose the Install from a list or specific location (Advanced) selection and click Next.Figure 62: Found New Hardware Wizard Screen 3Select the option

© CES Wireless Technologies Corp – 2011 Page 46 of 50

© CES Wireless Technologies Corp – 2011 Page 47 of 50

© CES Wireless Technologies Corp – 2011 Page 48 of 50

Figure 64: Found New Hardware Wizard Screen 5Once the drivers have been installed this final form will be displayed.Click on Finish. The Windows Found

WARRANTYComplete Warranty details can be found at the CES Wireless web site: www.ceswireless.comCES Wireless Technologies Corp., (CES Wireless), warra

Revision HistoryRevision Description Revised By Date1.0 Initial Release for GPS-206 D. Hamilton 04-21-20091.1Added Advanced Input Configuration for th

1.0 IntroductionThis manual contains instructions on how to configure the GPS-201, GPS-202 GPS-205, GPS-206, GPS-208 and the PT-101 using DP-1000S ver

Figure 1: Device SelectionIf the configuration values entered were saved when the application was closed (optional) those values will be read and the

2.2 System SetupThe System Information section contains the fields necessary to program the GPS-201, GPS-202, GPS-205, GPS-206, GPS-208 or the PT-101

Unit ID: A unique Unit ID is entered in this field. This value must be unique for each unit on the system.If the device is to be used on FleetLinc or